                   .:                     :,                                          
,:::::::: ::`      :::                   :::                                          
,:::::::: ::`      :::                   :::                                          
.,,:::,,, ::`.:,   ... .. .:,     .:. ..`... ..`   ..   .:,    .. ::  .::,     .:,`   
   ,::    :::::::  ::, :::::::  `:::::::.,:: :::  ::: .::::::  ::::: ::::::  .::::::  
   ,::    :::::::: ::, :::::::: ::::::::.,:: :::  ::: :::,:::, ::::: ::::::, :::::::: 
   ,::    :::  ::: ::, :::  :::`::.  :::.,::  ::,`::`:::   ::: :::  `::,`   :::   ::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  :::::: ::::::::: ::`   :::::: ::::::::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  .::::: ::::::::: ::`    ::::::::::::::: 
   ,::    ::.  ::: ::, ::`  ::: ::: `:::.,::   ::::  :::`  ,,, ::`  .::  :::.::.  ,,, 
   ,::    ::.  ::: ::, ::`  ::: ::::::::.,::   ::::   :::::::` ::`   ::::::: :::::::. 
   ,::    ::.  ::: ::, ::`  :::  :::::::`,::    ::.    :::::`  ::`   ::::::   :::::.  
                                ::,  ,::                               ``             
                                ::::::::                                              
                                 ::::::                                               
                                  `,,`


http://www.thingiverse.com/thing:2270859
"Mark V" Battlefield 1 by Treespirit is licensed under the Creative Commons - Attribution license.
http://creativecommons.org/licenses/by/3.0/

# Summary

ATTENTION !!!
This is not an easy print!
You should know your printer very well.
This print is built like a model kit!
Basic assembly skills are necessary.

So, this is the MARK V tank from Battlefield 1.
Everything is based on the ingame model...from which I could not use a single part :(
So I had to model everything from scratch. But I´m more than happy with the result :)
I have added a sliced version for people with smaller printbeds (like me).
Dimensions are: 16 x 7,5 x 5,5 cm
I know that the paint job is not 100% accurate to the game but I like it that way. Show me that you can do better ;)

Have fun printing!
& don´t forget to check the instructions below ;)

# Print Settings

Printer: Kossel mini
Rafts: Doesn't Matter
Supports: No
Resolution: 0,1
Infill: 15-20%

Notes: 
Most parts need NO support! 
Filename says _support if you need it!

# Post-Printing

![Alt text](https://cdn.thingiverse.com/assets/0f/03/76/b8/ee/Page1.jpg)
If you are using the non sliced Version, skip Step 0.1

Yes, I know, gluing sliced version 1.1 - 4.2 is a pain in the a**.
Lay the parts down on a flat surface and use as less glue as possible. Secure them with a piece of tape while the glue dries.

![Alt text](https://cdn.thingiverse.com/assets/d9/1f/d5/4e/4f/Page2.jpg)

![Alt text](https://cdn.thingiverse.com/assets/2c/a3/55/d1/0a/Page3.jpg)

![Alt text](https://cdn.thingiverse.com/assets/dc/26/ea/1b/2a/Page4.jpg)