                   .:                     :,                                          
,:::::::: ::`      :::                   :::                                          
,:::::::: ::`      :::                   :::                                          
.,,:::,,, ::`.:,   ... .. .:,     .:. ..`... ..`   ..   .:,    .. ::  .::,     .:,`   
   ,::    :::::::  ::, :::::::  `:::::::.,:: :::  ::: .::::::  ::::: ::::::  .::::::  
   ,::    :::::::: ::, :::::::: ::::::::.,:: :::  ::: :::,:::, ::::: ::::::, :::::::: 
   ,::    :::  ::: ::, :::  :::`::.  :::.,::  ::,`::`:::   ::: :::  `::,`   :::   ::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  :::::: ::::::::: ::`   :::::: ::::::::: 
   ,::    ::.  ::: ::, ::`  :::.::    ::.,::  .::::: ::::::::: ::`    ::::::::::::::: 
   ,::    ::.  ::: ::, ::`  ::: ::: `:::.,::   ::::  :::`  ,,, ::`  .::  :::.::.  ,,, 
   ,::    ::.  ::: ::, ::`  ::: ::::::::.,::   ::::   :::::::` ::`   ::::::: :::::::. 
   ,::    ::.  ::: ::, ::`  :::  :::::::`,::    ::.    :::::`  ::`   ::::::   :::::.  
                                ::,  ,::                               ``             
                                ::::::::                                              
                                 ::::::                                               
                                  `,,`


http://www.thingiverse.com/thing:3667617
B-17 Bomber With Moving Parts by CloneTrooper501 is licensed under the Creative Commons - Attribution license.
http://creativecommons.org/licenses/by/3.0/

# Summary

This is a model of a B-17 Flying fortress bomber. It has spinning propellers, rotating turrets and operational landing gear.

# Print Settings

Printer Brand: Creality
Printer: Ender 3
Rafts: Doesn't Matter
Supports: Yes
Resolution: .08-.1
Infill: 15%
Filament_brand: Superfila
Filament_color: White
Filament_material: PLA

Notes: 
I printed this at 400% the original scale and the small parts functioned.

# Post-Printing

## Instructions

1. Print one of all the parts with "body" in the name, engine left parts one and two, engine 
    right parts one and two, and the two turrets. 
    Print two outer engines, landing gears, wheels, and wheel plugs. 
    Print four propellers and propeller plugs.
2. Slide wheels on to the axles on the landing gear pieces. Glue the wheel plugs on to the 
    end of the axle to keep the wheel from sliding off.
3. Insert the hole in the landing gear pieces into the axles on the engine part ones. Have 
    the wheel axle face away from the engine piece.
4. Glue the engine part two pieces to the other assemblies. You may need to sand the 
    wheel plug down so it fits into the slot.
5. Insert the propeller into the rod on the propeller plug. Repeat four times. Put one 
    propeller assembly into the hole on each engine. 
6. Glue the engines with landing gear on the inner spots on the large wings. Have the 
    wheels face away from the body, towards the tip of the wings.
7. Glue the Large wings to their respective body sections. The wings should point upwards 
    a little.
8. Glue the small wings to their respective body sections.
9. Insert the lower turret into the half circle area of one body section. Do the same with the 
    upper turret.
10. Glue the two body sections together.
11. Enjoy your Plane!